Mint-flavored Robert B. Stevenson, Columbus, Ohio
cotton rolls D.D.S., M.S., M.A.
Pressure-indicator paste is often used by dentists while making adjustments to denture bases. Typically, the paste is applied to the tissue surface of the denture before its insertion. Two small pieces of moist cotton roll are placed in the patient’s mouth and the patient is instructed to chew the cotton pieces between the molars, one piece on either side. The denture is then removed and inspected for signs of excessive pressure. Patients commonly remark about the tastelessness of the cotton rolls. Mint flavoring can be added to ordinary cotton rolls by the following method: 1. Cut approximately 50 cotton rolls into pieces one quarter to one half inch in length by using bandage scissors or similar utensil.
Reprint
requests
to:
DR. ROBERT B. STEVENSON 3600 OLENTANGY RIVER RD. COLUMBUS, OH 43214
10/4/22648
Simplified
2. Place one drop of peppermint oil (Lorann Oils, Inc., Lansing, Mich.) on one piece of cotton roll and mark it with an ink spot. Place the piece in the bottom of a suitable container. The container must have a lid and should be just large enough to hold all of the cotton pieces. A plastic denture cup (Den-Shur-Cup, Rugby Labs, Inc., Rockville Centre, N.Y.) works well. 3. Place the remainder of the cotton pieces in the container and close the lid. After 1 week all of the cotton pieces will have a mild peppermint flavor. Once the cotton pieces have acquired the mint flavor, the piece with the ink spot should be removed and discarded to prevent accidently giving it to a patient for chewing.
method for placing
glass ionomer
cement bases
Elias Grego, D.D.S. Tecamachalco, Mexico When teeth are prepared according to the concept of minimal tooth reduction, it is often difficult to apply a pulp-protecting product such as glass ionomer cement at 1014122646
the bottom of the cavity without touching the walls of the preparation. Excess glass ionomer cement on the walls of a narrow cavity preparation is difficult to remove. This problem can be easily solved by using a syringe to place the base in the bottom of the tooth preparation. PROCEDURE 1. Isolate the tooth with a rubber dam. 2. Prepare the tooth and remove the decay (Fig. 1). 3. Clean the tooth with pumice that does not contain fluoride; wash and dry it.
Fig. 1. Prepared tooth isolated with rubber dam and clamp. 740
Fig. 2. Centrix C-R syringe with plastic tip. DECEMBER
1990
VOLUME
84
NUMBER
6
cotton rolls D.D.S., M.S., M.A.
Pressure-indicator paste is often used by dentists while making adjustments to denture bases. Typically, the paste is applied to the tissue surface of the denture before its insertion. Two small pieces of moist cotton roll are placed in the patient’s mouth and the patient is instructed to chew the cotton pieces between the molars, one piece on either side. The denture is then removed and inspected for signs of excessive pressure. Patients commonly remark about the tastelessness of the cotton rolls. Mint flavoring can be added to ordinary cotton rolls by the following method: 1. Cut approximately 50 cotton rolls into pieces one quarter to one half inch in length by using bandage scissors or similar utensil.
Reprint
requests
to:
DR. ROBERT B. STEVENSON 3600 OLENTANGY RIVER RD. COLUMBUS, OH 43214
10/4/22648
Simplified
2. Place one drop of peppermint oil (Lorann Oils, Inc., Lansing, Mich.) on one piece of cotton roll and mark it with an ink spot. Place the piece in the bottom of a suitable container. The container must have a lid and should be just large enough to hold all of the cotton pieces. A plastic denture cup (Den-Shur-Cup, Rugby Labs, Inc., Rockville Centre, N.Y.) works well. 3. Place the remainder of the cotton pieces in the container and close the lid. After 1 week all of the cotton pieces will have a mild peppermint flavor. Once the cotton pieces have acquired the mint flavor, the piece with the ink spot should be removed and discarded to prevent accidently giving it to a patient for chewing.
method for placing
glass ionomer
cement bases
Elias Grego, D.D.S. Tecamachalco, Mexico When teeth are prepared according to the concept of minimal tooth reduction, it is often difficult to apply a pulp-protecting product such as glass ionomer cement at 1014122646
the bottom of the cavity without touching the walls of the preparation. Excess glass ionomer cement on the walls of a narrow cavity preparation is difficult to remove. This problem can be easily solved by using a syringe to place the base in the bottom of the tooth preparation. PROCEDURE 1. Isolate the tooth with a rubber dam. 2. Prepare the tooth and remove the decay (Fig. 1). 3. Clean the tooth with pumice that does not contain fluoride; wash and dry it.
Fig. 1. Prepared tooth isolated with rubber dam and clamp. 740
Fig. 2. Centrix C-R syringe with plastic tip. DECEMBER
1990
VOLUME
84
NUMBER
6
