9 1987 by The Humana Press Inc. All rights of any nature, whatsoever, reserved. 0163-4984/87/1300-0219502.00
X-Ray Microtomography of Biological Tissues Using Laboratory and Synchrotron Sources J. C. ELLIOTT, *'1 D. K. BOWEN, 2 S. D. DOVER, 3 AND S. T. DAVIES2
~Department of Biochemistry, The London Hospital/Vledical College, Turner Street, London E! 2AD, UK; 2Department of Engineering, University of Warwick, Coventry, CV4 7AL; and 3Department of Biophysics, King's College, 26-29 Drury Lane, London WC2B 5RL ABSTRACT X-ray microradiography is a well established technique for the study of biological structures in which the projected absorption is measured, usually with photographic film or resist. If scanning X-ray microradiography with a 15-1xm beam, 2-D scanning, and photon counting is used, more accurate results can be obtained and real-time experiments undertaken. Addition of a rotation axis allows computerized axial tomography to be done at a resolution of 15 ~xm. This technique overcomes the inherent difficulty of microradiography that all detail perpendicular to the plane of the specimen is superimposed. This method has been applied to the study of the 3-D mineral distribution in a 0.8 x 0.8 mm column of human cortical bone with a laboratory X-ray source. Calculation of the wavelength dependence of the linear absorption coefficient for liver and bone shows that, for a choice of wavelength in the range of 3-0.4 • (4-30 keV), the specimen thickness can be from 100txm-2 cm and 10 txm-3 mm, respectively. Synchrotron X-radiation has the potential for better resolution because of the higher intensity, which allows the use of a narrower beam. There is also the possibility of determining individual element 3-D distributions from measurements on either side of the absorption edges because of the continuous nature of the spectrum and also the possibility of doing this from X-ray fluorescence measurements. To investigate these possibilities, a tomographic apparatus has been built *Author to whom all correspondence and reprint requests should be addressed. Biological Trace Element Research
219
Vol. 13, 1987
220
Elliott et al. based on the availability of accurately ground, tungsten carbide balls. Metrological assessment shows that the specimen remains within
X-Ray Microtomography of Biological Tissues Using Laboratory and Synchrotron Sources J. C. ELLIOTT, *'1 D. K. BOWEN, 2 S. D. DOVER, 3 AND S. T. DAVIES2
~Department of Biochemistry, The London Hospital/Vledical College, Turner Street, London E! 2AD, UK; 2Department of Engineering, University of Warwick, Coventry, CV4 7AL; and 3Department of Biophysics, King's College, 26-29 Drury Lane, London WC2B 5RL ABSTRACT X-ray microradiography is a well established technique for the study of biological structures in which the projected absorption is measured, usually with photographic film or resist. If scanning X-ray microradiography with a 15-1xm beam, 2-D scanning, and photon counting is used, more accurate results can be obtained and real-time experiments undertaken. Addition of a rotation axis allows computerized axial tomography to be done at a resolution of 15 ~xm. This technique overcomes the inherent difficulty of microradiography that all detail perpendicular to the plane of the specimen is superimposed. This method has been applied to the study of the 3-D mineral distribution in a 0.8 x 0.8 mm column of human cortical bone with a laboratory X-ray source. Calculation of the wavelength dependence of the linear absorption coefficient for liver and bone shows that, for a choice of wavelength in the range of 3-0.4 • (4-30 keV), the specimen thickness can be from 100txm-2 cm and 10 txm-3 mm, respectively. Synchrotron X-radiation has the potential for better resolution because of the higher intensity, which allows the use of a narrower beam. There is also the possibility of determining individual element 3-D distributions from measurements on either side of the absorption edges because of the continuous nature of the spectrum and also the possibility of doing this from X-ray fluorescence measurements. To investigate these possibilities, a tomographic apparatus has been built *Author to whom all correspondence and reprint requests should be addressed. Biological Trace Element Research
219
Vol. 13, 1987
220
Elliott et al. based on the availability of accurately ground, tungsten carbide balls. Metrological assessment shows that the specimen remains within
